Brakes - How They Work

This time we’re going to look at just how brakes do what they do, and ways to improve them. Without a doubt the most important point to get sorted at the outset is just what makes brakes do their thing - FRICTION. The sole purpose of the brake set-up on any vehicle .....

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

Distributors - working basics

To maximise power and economy potential from any engine, burning the compressed fuel/air mixture at precisely the right point throughout the engines entire rpm range is essential.

Terminology -
TDC - Top Dead Centre
BTDC - Before Top Dead Centre
Dizzy - distributor
CR - compression ratio

To maximise power and economy potential from any engine, burning the compressed fuel/air mixture at precisely the right point throughout the engines entire rpm range is essential. This ‘point’ is generally somewhere before the piston reaches TDC on its power stroke described in degrees - i.e. 10 degrees BTDC. This point isn’t constant throughout the rpm range. Low rpm values are normally less than high ones.

Ultimately the dizzy provides this spark at exactly the right point to effect this burn.

SU CARBURETTORS - HOW THEY WORK

Basic knowledge Even though the SU carburetter (carb) is a very basic yet precise instrument, some fundamental understanding on just how it works is needed to be able to deal with common problems and tuning. Following is as basic a description of what's going on that I can manage! First you need to be comfortable with the main aim of any carb - to supply the engine with a finely atomized fuel/air mixture in the right strength for all operating conditions. This means from idle to flat out and everything in-between. All carbs achieve this using the same method - a venturi or choke (restriction) is used to speed up the velocity of the in-coming air to create a reduction in pressure. This is used to draw fuel from the float chamber via a suitably sized jet hole into the air stream, and hence into the engine. The perfect carb will supply the engine with optimum mixture for both maximum power throughout the full throttle-angle range (variable restriction - as in butterfly and spindle) a

C-AJJ3329 Works 4 Lamp BarMSA1101 Budget Black 4 Lamp Bar

Fitting Instructions

Remove grille and overriders (if fitted the overriders can’t be refitted) Remove the centre fixing nut from the bumper, fit the centre support bracket using the bumper nut and washer, bending the bracket towards the apron mark off and drill hole after offering bar up. Loosely assemble the 2 end brackets and then check alignment. The right angled sections of the brackets bolt to the front panel and lower part of the apron. Contents: Lamp Bar Right Hand Bracket Left Hand Bracket Centre Bracket

Lubrication - Oil, What it does and how it works

It’s criminal. Folk spend fortunes putting together super-sonic motors, only to skimp on the oil they use. Why? Oil’s oil right? Wrong.

Historical Article-August 1994-The truth, the whole truth and nothing but the tr...

THE TRUTH, THE WHOLE TRUTH AND NOTHING BUT THE TRUTH! When we started on the electronic management system for our 8-Port, it was also our idea to make a system for the latest fuel injection Minis.At the same time,Glyn Swift (Swiftune) had started work on a unit with M.B.E.Electronics,but even at a fairly advanced stage, it was still having reliability problems,so it was withdrawn from the market. Swiftune,as you will know from previous articles....

SUSPENSION - Basic set-up method

Time to arrange all those agonised over, carefully selected and applied suspension components to give of their best.

Suspension - Basic set-up method

part numbers: TOOL10, TOOL11, HILO, HILO-01

Time to arrange all those agonised over, carefully selected and applied suspension components to give of their best.

This is one of those subjects viewed as a ‘black art’, largely because of lack of understanding and confusion. The confusion part is because folk encompass the whole suspension set-up deal with suspension arrangement and design, lack of understanding instilling terror at the thought of ‘fiddling’ with the suspension components. The latter also fuelled by the knowledge that expensive specialist measuring equipment is needed. Well, there is no black art – you can work the magic. More a case of a long day...

SUSPENSION - Basic Priorities

Suspension - Basic priorities for improved suspension performance. Having studied the 'Suspension - Terminology' article you should now have a ‘job description’ understanding of previously possibly un-comprehended words associated with suspension control. Now - what to do with it? The first thing we need to establish is an order of priority before distributing hard-earned 'beer vouchers' in all directions. Fortunately, this is a good deal less complicated than is generally believed. Despite the five main factors that control the front suspension geometry – kingpin inclination, caster angle, camber angle, track, and bump-steer – we are only really able to alter three of those easily. King-pin inclination is non-adjustable, as it’s a feature of where the swivel-pins are mounted on the hub at the factory. It will alter as other adjustments are made, but we can do nothing easily about correcting/optimising it independently, as these are fixed in position on the swivel hub.

Camshafts - Scatter cams, pros and cons

To scatter or not to scatter, that is the question. This whole 'scattering' deal has befuddled many. The only real prose produced on the subject, and 'advice' handed out by many so-called 'specialists' tends to be somewhat tainted with large chunks of mysticism - inferring there's some kind of black art involved. The simple fact is the principle is very basic and easy; it's getting a cam with the right profile and figures applied to it that will actually work as a scatter profile that's the hard part. And this article does not mean I am all for scatter pattern cams. I will illuminate… We are all pretty much aware that the A-series is a real oddity, largely because of the siamese (shared) port work - cylinders 1 & 2 share an inlet port, cylinders 3 & 4 share an inlet port, and cylinders 2 & 3 share an exhaust port. Very weird compared to the more familiar head designs found on almost every other engine type that has one inlet and one exhaust port per cylinder.

Camshaft Design

Elgin Cams is a company that is a direct descendent of such famous California specialists as Isky, Delong, Winfield, etc. etc. Elgin has taken the art of cams into the science of the '90's. Computer designed and handcrafted workmanship guarantee a first class camshaft. Custom designed cams are a specialty. Part No Applications: CAM001, CAM002, CAM003, CAM004, CAM005, CAM006, CAM007 Elgin has made cams or sold his design to General Motors, Ford Motor Co., Nissan Corp., Zakespped International, Porsche Motor Sports, Winston Cup "Engine Builders. Elgin has the largest percentage of cams used at the SCCA Runoffs from GT-1 to Formula-V. He also has provided original or new technology for antique and vintage racers. Much information has been recorded about the four stroke internal combustion engine and yet only a small percentage of people really understand how it works and fewer people know how to modify an engine to suit their needs.

Clutch - Drive Strap Alignment

Drive Strap Alignment If the pressure plate clutch plate friction face needs re-surfacing, get it machined to clean it up. Make sure the engineering company doing the job records the amount taken off as once done, the recorded amount needs removing from the tops of the 'horns' that stick up to ensure proper clamping force is achieved. If this is not done, clutch slip is inevitable. If using a pressure plate of unknown history, it is IMPERATIVE the clutch drive straps are set at the correct height. Many get this wrong and end up with a slipping clutch for some seemingly unfathomable reason. The following should also be carried out if the flywheel has been machined, or of unknown history also: Place the pressure plate 'horns' upper-most on something to hold it off of the work surface but not interfere with clutch plate or flywheel. Place the clutch plate in position, with the protruding primary gear spline boss on the underside facing the work surface Place the flywheel in positi

DIAPHRAGM SPRING - Verto types including injection

The Verto/Valeo type diaphragm included the pressure plate in its assembly, much like a 'normal' car set-up. The spring being of the 'finger' type as opposed to the disc spring used on earlier, three-piece assemblies. There were originally three diaphragm specifications using progressively stronger springs - small-bore, big-bore, and Metro Turbo. Later joined by the type used on the injection cars, though most definitely not interchangeable. Initially, the biggest problem was the Turbo ones were never really available on their own. If you wanted one you had to buy a whole clutch/flywheel assembly - the cost exorbitant. Rover originally believed that if the clutch plate was worn out, then the flywheel and pressure plate would be too. It has only been recent times that the diaphragm/pressure plate has been available on it’s own - but not until after the Turbo unit became unavailable. Even that has changed recently with the cessation of the Turbo diaphragm as a service part.

DIAPHRAGM SPRING - Verto types including injection

The Verto/Valeo type diaphragm included the pressure plate in its assembly, much like a 'normal' car set-up. The spring being of the 'finger' type as opposed to the disc spring used on earlier, three-piece assemblies. There were originally three diaphragm specifications using progressively stronger springs - small-bore, big-bore, and Metro Turbo. Later joined by the type used on the injection cars, though most definitely not interchangeable. Initially, the biggest problem was the Turbo ones were never really available on their own. If you wanted one you had to buy a whole clutch/flywheel assembly - the cost exorbitant. Rover originally believed that if the clutch plate was worn out, then the flywheel and pressure plate would be too. It has only been recent times that the diaphragm/pressure plate has been available on it’s own - but not until after the Turbo unit became unavailable. Even that has changed recently with the cessation of the Turbo diaphragm as a service part.

DIAPHRAGM SPRING - Pre-Verto types

I'm ignoring the old original spring-type jobs here for the same reasons I wouldn't suggest using their flywheels! The first two can be lightened, see accompanying diagram. Limit removal of metal on the rear face to 0.120" to be safe, 0.150" if you're feeling brave/lucky. The third can be further lightened by carrying out the machining operation on the rear face as indicated in the diagram and as per previously stated dimensions. Do not remove any more material than indicated for any of these pressure plates as it will not only reduce their strength, but will also cause over-heating of the clutch. Too little material will not be able to absorb any excessive heat generated during spirited driving! Bear in mind what was said about lightened standard cast iron flywheels - the same applies here. Under no circumstances use lightened standard cast iron pressure plates in ANY competition disciplines. The SG iron items are suitable for full race use despite lightening operations, although f

PRESSURE PLATE- Pre-Verto & Verto types

There is an astonishing five other types generally available. For high-tech ones see 'Flywheels & Pressure plates - technical advances' part numbers: 22A598, 22G270, C-AHT230, Apart from very first one that should be avoided at all costs (cast in part no.2A3509), there is an astonishing five other types generally available. For high-tech ones see 'Flywheels & Pressure plates - technical advances'. 22A598 - Number cast in. Standard-grade cast iron 22G270 - Number cast in. High-grade cast SG iron as fitted to Coopers and Cooper Ss Quinton Hazel - Triangular in shape, but only standard-grade cast iron. C-AHT230 - Mini Spares high-grade SG cast iron, but cast pre-lightened. Farndon Engineering - Machined from steel billet. The first two can be lightened, see accompanying diagram. Limit removal of metal on the rear face to 0.120" to be safe, 0.150" if you're feeling brave/lucky. The third can be further lightened by carrying out the machining operation on the rear face as indica

CLUTCH PLATES - Verto types, including injection

There is only one original Verto/Valeo clutch plate and is fashioned more like a ‘conventional’ clutch plate - it has a sprung centre section. Four springs around the centre section of the plate take up shock, and supposedly reduce the likelihood of judder. It was an attempt by Rover to improve the clutch take-up and engagement to make is more like a 'modern' car. Except it didn't. The engagement feels wooly at best, and judders horribly at worst. They even went as far as making two plates, one for small-bore, one for big-bore. The difference being the centre spring tensions! From experience, judder is caused by undulating flywheel/pressure plate surfaces, or ‘breakfast cereal packet’ lined non-genuine plates. It's OK, but if any warming up of the engines output is considered, definitely go for the pre Verto plate. This will fit with the Verto set-up and is a cheaper into the bargin. The Metro Turbo had a Verto flywheel type, but the clutch had the more familiar solid centre of the p

GEARBOX - Limited Slip Diffs; necessary parts for installation.

Fitting an LSD isn't as simple as replacing the diff cage unit. In all cases a certain degree of diff housing modifications is needed - material needing to be ground/filed away to provide clearance for larger diff housing cases and crown wheel bolts. Although it has to be said the Quaife diff is supposed to fit without these mods. I've never found that. The design and manufacture of the LSD to facilitate any other function other than that of a standard 'open' diff assembly precludes use of standard CWPs. So one suitable for an LSD is needed. Naturally Mini Spares/Mania supply these in an extensive range of FD ratios. The output shafts are also different. A much thicker spline type is used within the LSD assembly. Consequently a suitable pair of LSD-compatible output shafts are needed. Some folk still insist on running the archaic, power consuming Hardy-Spicer type driveshaft to diff joints - although this is the only real option for rallying unless a change in driveshaft assembly

Gearbox - Common Sources of Problems

Seems recently a number of folk have been suffering gearbox failures of various sorts; nothing new there then except they've popped their heads up over the parapet to ask why. part numbers: C-22A1738, C-22A1731, 88G396, CHM141, 13H9513, 22A611, 22A610, TSP100390, TSP100400, 22G2595 Under closer scrutiny this time around the reasons for bearing failures, gear tooth breakage, and jumping out of gears to name but a few are the sources of hassle. Just like in engine building, a gearbox needs careful and proper attention when building it up. It isn't a difficult job, and most competant DIY mechanics can make a decent job of it. But, just like engine building, it's the knowledge of what to look for prior to and during the build that sets the 'professional' builders apart. Hopefully resulting in a more reliable, perfectly functioning unit. One generally over-looked, or completely missed, feature is where the layshaft is carried in the gearbox casing itself. The shaft merely runs in tw