TOOL 11 TRACKING GAUGE INSTRUCTIONS

TOOL11 is a supremely simple device to use, essentially an oversized vernier calliper.

Although a billiard table like surface is not needed, it is sensible to have the car on something like level ground without any of the wheels in dips or on lumps. Set the steering straight ahead and roll the vehicle back and forth a couple of times to settle the suspension. Resting the gauge on the ground in front of the vehicle with the arms at each end elevated, set the gauge to suit vehicle track width by releasing the two clamp bolts and sliding the two halves apart/together until the desired position is achieved, positioning the measuring tips at half overall wheel/tyre height (i.e. a line drawn horizontally through the hub centre to intersect the wheel/tyre outer edges) on either the wheel rim or tyre wall then pinch...

SUSPENSION - Basic set-up method

Time to arrange all those agonised over, carefully selected and applied suspension components to give of their best.

Suspension - Basic set-up method

part numbers: TOOL10, TOOL11, HILO, HILO-01

Time to arrange all those agonised over, carefully selected and applied suspension components to give of their best.

This is one of those subjects viewed as a ‘black art’, largely because of lack of understanding and confusion. The confusion part is because folk encompass the whole suspension set-up deal with suspension arrangement and design, lack of understanding instilling terror at the thought of ‘fiddling’ with the suspension components. The latter also fuelled by the knowledge that expensive specialist measuring equipment is needed. Well, there is no black art – you can work the magic. More a case of a long day...

Primary Gear - Bush Replacement

With the cost of new primary gears spiralling ever upwards, and the availability of good, serviceable used ones, fitting new bushes to existing gears is becoming a more common solution. For some reasons for bush failures and rectification to stop it re-occurring, see article Primary gear - Bush problems. Since there is no useful information given in any of the workshop or DIY manuals on this subject, following is my approach to dealing with the issue. The first thing to get to grips with is which bush is which. This has added an element of confusion to many conversations I have had with folks on this subject, so - the FRONT bush is the one nearest the engine block, the REAR bush is the top-hat one nearest the flywheel. This is because the front of the engine is actually the radiator end - quoted in 'in-line' engine-speak. The REAR bush is the same on all primary gears - be they for small or large bore engines. The FRONT bush is different for each though; the small-bore one is smaller

Idler Gear - Setting End Float

A fairly crucial part of how the idler gear operates is its tolerances and running clearances. part numbers: 22A1545, 22A1546, 22A1547, 22A1548, 22A1549, DAM4822, DAM4823, DAM4824, DAM4825, GUG705563GM, AAU8424, ADU6033, CCN110, 2A3643, 22A152, 53K547, Terminology: DTI - Dial Test Indicator End float is a continual problem as folk either ignore it through ignorance or lack of accessible information on how to do it, or belief special tools are needed. Also, later factory assembled engine units (from about 1992 onwards) were built up using whatever shims and thrust washers were available, since Rover were not making regular orders for all shim/washer sizes due to the forthcoming end of production. Consequently, many units left Rover with incorrect (usually too big) clearances. The idler gear was no exception. Too tight a clearance and the idler gear will either seize solid when it gets hot, or destroy the thrust washer thrust faces in the comparably soft aluminium gearbox and t

Primary Gear – Bush Problems

Although not of immediate interest to many road-runners/street-burners, mainly accorded to the racing scene, it seems to be a perplexing problem to a very large number of folk around the world, and has burned up plenty of telephone time.

part numbers: 13H2934, LUF10005, CE12, 22G109, DAM8889, DAM8887

With the cost of new primary gears spiralling ever upwards, and the availability of good, serviceable used ones, fitting new bushes to existing gears is becoming a more common solution. For some reasons for bush failures and rectification to stop it re-occurring, see article 'Primary gear - Bush problems'. Since there is no useful information given in any of the workshop or DIY manuals on this subject, following is my approach to dealing with the issue.

The first thing to get to grips with is which bush ...

Brakes - Fitting Discs and Required Ancillaries

What you actually need for the disc/drum conversion is pretty straightforward. Disconnect the steering arms, top and bottom swivel-pins, CV joint, and flexible brake pipes at the subframe - that’s it. There are, however, a number of ancillaries to consider.

Basics

Basics Fitting discs designed for the Mini is easy enough. Just make sure you use CV gaiters for the disc-brake set-up - these have a different bellows shape to stop the gaiter rubbing the inside of the hub. The drum type will rub, then split, shedding grease all over the place. Moly grease is mighty mucky stuff to deal with and doesn't assist braking at all! A tip for racers - to stop the gaiters over-expanding when getting very hot and imitating the aforementioned, put either a decent sized split pin or (my favorite) a piece of very small bore pipe - as in the type supplied with WD40 aerosols, etc. - under the retaining strap on the drive shaft. This allows air to escape and return,

Brakes - Pipe End Flares

One day I'm going to have to try and assess just how it is that every now and again I get a 'run' on folks asking me about a specific problem. These problems exist all year round, year in, year out. And said problems crop up throughout the year. But - every now and then there's a blood-rush on a certain issue. Just recently that issue has been brake pipe ends. The bit that seals the pipe off against it's relevant fitting. There are two types of end - male and female. The male end is convex in shape, the female concave. The male end is used where a male pipe union (nut) is used on the brake pipe - that's a nut with an external thread - that will be screwed into a female fitting such as found in a wheel cylinder or master cylinder. The female end is used where a female pipe union (nut) is used on the brake pipe - a nut with an internal thread - and will be mated to a male fitting such as found on rear flexible brake pipes. Under no circumstances should you mix the too up as the brake p

Cylinder head - What can easily be achieved

During a discourse with the editorial staff at Mini Mag, it was decided the build feature presented an ideal opportunity to demonstrate just exactly what such an engine build is capable of in days where it's generally believed you have to have an all-singing, all-dancing 1380cc engine to have an enjoyable road burner - leaving those with very limited budgets a little depressed. During a discourse with the editorial staff at Mini Mag, it was decided the build feature presented an ideal opportunity to demonstrate just exactly what such an engine build is capable of in days where it's generally believed you have to have an all-singing, all-dancing 1380cc engine to have an enjoyable road burner - leaving those with very limited budgets a little depressed. So the idea was to finish the engine off using a relatively 'mild' specification to maximise drivability. The camshaft used was the fantastically versatile Swiftune Racing SW5 profile that provides drive from nowhere up to 7,000rpm - d

Rocker gear - General compendium

Whether you’re building a solid road performer or fire-breathing monster, the main goal is to improve air/fuel flow into the engine. The more you can get in, the more power you can get out. Cheapest chunk of power improvement comes from sorting the asthmatic manifolding and exhaust by applying a stage one kit. Then what? Considering the ‘get more in to get more out’ theme, the main restriction - all else being equal - is the valves and their behavior. How big they are, how efficient they are and how long they’re open for determines how much gets in with each gulp each bore/piston makes. Modified cylinder heads are popularly next, although it has to be said that although a well modified cylinder head will improve performance, the gain against cost is nowhere near that given by the ‘stage one’ kit application. A good stage one kit’s improvement verses cost is around £12.50 per 1 hp, a decent modified head typically £30 per 1hp - dependent on application. Hmm.

Engine - 1098, Initial Tuning

The 1098 (1100) engine has had a lot of bad press over the years - largely because of early experiences when trying to tune the motor brought about problems with the then standard components available - they simply were not up to taking any real punishment as experienced in racing.

See bottom for useful part numbers.

This fallacy was handed down generation to generation like some scary bedtime story. Those that have used the unit in more recent years, employing more capable componentry know what a demon motor this can be. Following is an initial look at what it will do with a little modification - the results compared directly with it's smaller brother the 998 for illustration of the potential.

Abridged History
When the Mini was first conceived it ustilised a de-stroked version of the then quite remarkable 948cc A-series engine.

Injection - Tuning Update 03.14.03

This program of development embarked upon by myself and colleague Mike Barratt (MBE, Lincoln 01522 545189) was instigated by Keith Dodd, owner of Mini Spares centre. His instructions were for us ....

Thread Locking Compounds - Application

This is the frequently abused and mis-used stuff dolloped on to bolts/nuts to stop them coming undone. Having seen and heard of many horror stories concerning this stuff, I thought a few words of caution and common sense wouldn't go amiss.

There is a plethora of types on the market with no easy reference as to which to use for what application except in certain cases. Loctite have a very useful guide, their dealers generally able to help with choosing which is best for any given application. The trouble comes when folk buy stuff unwittingly from their local 'do it all' motorist/car spares place. Good stuff is expensive, and it doesn't go all that far. But at least it does its job when used in the correct applications. Unfortunately many buy a cheaper variety with not quite the same application strength, and then apply twice as much hoping it will do the job. It doesn't.

Thread Locking Compounds - Application

This is the frequently abused and mis-used stuff dolloped on to bolts/nuts to stop them coming undone. Having seen and heard of many horror stories concerning this stuff, I thought a few words of caution and common sense wouldn't go amiss.

There is a plethora of types on the market with no easy reference as to which to use for what application except in certain cases. Loctite have a very useful guide, their dealers generally able to help with choosing which is best for any given application. The trouble comes when folk buy stuff unwittingly from their local 'do it all' motorist/car spares place. Good stuff is expensive, and it doesn't go all that far. But at least it does its job when used in the correct applications. Unfortunately many buy a cheaper variety with not quite the same application strength, and then apply twice as much hoping it will do the job. It doesn't.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

GEARBOX - How they work

Having decided on or even implemented a course of action to bolster the performance of your Mini’s engine, maximising it’s potential should encompass a good look at the gearbox.

Electrical - Terminal fixation

'To solder or not to solder, that is the question'

Despite having spent something in the order of 26 years delving into all things automotive and some 24 of those concentrating a great deal on the Mini, I have never assumed I know it all. In fact I'm very much one of those to support the 'you never stop learning' theory. My latest endeavours to get out racing again have caused me to look at all things connected (sorry - pun) with racecar preparation - the wiring loom being one such item.

I decided to canvas everybody I knew that was involved with electronics and electrics to any degree to see what the latest state of ply was concerning fixing terminals to cables. 'To solder or not to solder, that is the question'. All my previous racecars (last one built about 14 years ago) had all the terminals carefully soldered on. It used to take me ages; taking a remarkably long time to become proficient at it - largely because of the 'not too hot' soldering iron I'd purchased to do th

Engine transplants - Engine to gearbox fitment

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings.

Terminology -
BBU - Big Bore Unit (1275cc based engines)
SBU - Small Bore Unit (850/998/1098cc based units)
FD - Final Drive

NOTE: This information is largely for transplanting large-bore engine units into small-bore engined Minis. For further information on up-grading transfer (drop) gears, refer to relevant separate article.

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings.

Engine transplants - Engine to gearbox fitment

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings.

Terminology -
BBU - Big Bore Unit (1275cc based engines)
SBU - Small Bore Unit (850/998/1098cc based units)
FD - Final Drive

NOTE: This information is largely for transplanting large-bore engine units into small-bore engined Minis. For further information on up-grading transfer (drop) gears, refer to relevant separate article.

Contrary to popular mis-guidance, all BBUs will fit all four-syncro gearboxes. It was only the three-syncro boxes that varied in casting dimensions causing hassles where 1275s were applied to 850/998 gearbox casings.

Engineering - Consistent measurements

During a recent discussion with a few overseas Mini brethren - who were experiencing various engine-related problems - something cropped up that I have always taken as granted (in the sense of ' a standard for the application'); the matter of consistency in measurements.

Now we're not talking about the sort of measurements you make with a ruler, since discrepancies of a small nature don't tend to matter a whole lot. No, we're talking about the sort of measurements made with fine measuring instruments such as micrometers or vernier calipers.

Now, the discussion that was going on was with reference to the best clearance to run between the bore and piston for a given piston type for race or street purposes. I hade quoted figures that I generally use for both situations for forged and for cast piston types.

Ignition - Establishing a TDC reference point

Establishing an accurate TDC reference point is of paramount importance when developing and monitoring ignition timing (and cam timing come to that). Terminology - TDC - Top Dead Centre BTDC - Before Top Dead Centre Establishing an accurate TDC reference point is of paramount importance when developing and monitoring ignition timing (and cam timing come to that). When an experienced engine builder assembles an engine - no matter whether for road or race - he will establish an accurate TDC indicator that can be used for ignition purposes. Usually contrived as a rigid pointer aligning to a corresponding mark on the crank pulley in a position easy to see with the engine installed. Unfortunately, many of us have to deal with engines that haven't had such attention to detail - so either have to make do with the standard ignition timing graduated scale if it's there or sort something else out.