C-AHT88 STAGE THREE SPEC SMALL BORE CYLINDER HEAD

Modified to give maximum performance gain for cost.

Exhaust seats Latest spec inserts for lead free fuel Modified to give maximum performance gain for cost. Combustion chambers, inlet and exhaust ports extensively reworked. Stone-ground finish in ports promotes ultimate fuel atomisation.

Cylinder head - What can easily be achieved

During a discourse with the editorial staff at Mini Mag, it was decided the build feature presented an ideal opportunity to demonstrate just exactly what such an engine build is capable of in days where it's generally believed you have to have an all-singing, all-dancing 1380cc engine to have an enjoyable road burner - leaving those with very limited budgets a little depressed. During a discourse with the editorial staff at Mini Mag, it was decided the build feature presented an ideal opportunity to demonstrate just exactly what such an engine build is capable of in days where it's generally believed you have to have an all-singing, all-dancing 1380cc engine to have an enjoyable road burner - leaving those with very limited budgets a little depressed. So the idea was to finish the engine off using a relatively 'mild' specification to maximise drivability. The camshaft used was the fantastically versatile Swiftune Racing SW5 profile that provides drive from nowhere up to 7,000rpm - d

Engine - 1098, Initial Tuning

The 1098 (1100) engine has had a lot of bad press over the years - largely because of early experiences when trying to tune the motor brought about problems with the then standard components available - they simply were not up to taking any real punishment as experienced in racing.

See bottom for useful part numbers.

This fallacy was handed down generation to generation like some scary bedtime story. Those that have used the unit in more recent years, employing more capable componentry know what a demon motor this can be. Following is an initial look at what it will do with a little modification - the results compared directly with it's smaller brother the 998 for illustration of the potential.

Abridged History
When the Mini was first conceived it ustilised a de-stroked version of the then quite remarkable 948cc A-series engine.

Cylinder head - Min Tec head range

I'm often asked about the range of cylinder heads I do for Mini Spares/Mini Mania, so here's the low-down…

Although the following range of heads accommodate specific fitments - like pre-1992 where by-pass hoses and heater take-offs on the clutch end of the head are used and post-1992 where neither of these exist, and on SPi (single point injection) heads where they don't usually have a threaded hole for the temperature sender - in reality it is easy to convert almost any of them to fit any other engine since holes are easily blocked off - or by-pass hoses not used, water pumps blanked off and drilled thermostats fitted (see articles on cooling/engine transplants). A list of which is what and what to do to each to convert is at the end of this article.

For more in-depth descriptions of the head specs, see article 'Cylinder head - About Min Tec Heads' - basically the valve sizes used have been decided on after extensive and in-depth flow test...

Cylinder head - Suitability basics

Whatever else owners do to their Minis by way of interior/exterior modifications or none at all, a very large proportion desire and search for an increase in engine performance.

See bottom for useful part numbers.

Now this may not be super-sonic speed-inducing power, it could just as well be for maximum economy. In either case, it's the engines volumetric efficiency (VE) under scrutiny - it's ability to breath in as much correctly proportioned air/fuel mix as possible in any given situation. Although the induction/exhaust system plays an important part, there are effectively two major factors that dictate performance increases - the camshaft and cylinder head. The induction and exhaust elements (stage one kits, exhaust systems, etc.) and camshafts are covered in various other articles in my 'Corner'. So here we'll have a look at cylinder heads and dispel some of the myths and legends surrounding them.

Engine - 998 tuning, further options

Following on from the easily bolted on performance enhancing components out-lined in the stage one section, we need to consider where to go to get more power output.

Terminology:
MSC/MM - Mini Spares Centre/Mini Mania
BBU - Big Bore Unit (refers to all 1275cc-based units)
SBU - Small Bore Unit (refers to all sub-1275cc units, here the 998)
BHP - Brake Horse Power
CR - Compression Ratio

To improve engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment. From here on in the power increases will cost commensurately more money. Power production of any engine, once the 'breathing apparatus' (induction/exhaust system) has been dealt with to cause no restriction ...