4 Synchro Gears 1979 on with 18MM Nose Mainshaft
-
LabelPart NamePart No.
-
1Idler gear, 37 teeth, shaft diameter .875” (22.225mm)TUB101310
-
2Idler gear shim .132”-.133” (3.35-3.37mm)DAM4822
-
2Idler gear shim .134”-.135” (3.40-3.42mm)DAM4823
-
2Idler gear shim .136”-.137” (3.45-3.47mm)DAM4824
-
2Idler gear shim .138”-.139” (3.50-3.53mm)DAM4825
-
31st motion shaft, 17 teeth, 998/1098ccDAM3092
-
31st motion shaft, 18 teeth, 1275GTDAM3167
-
31st motion shaft, 17 teeth, A PlusDAM4930
-
41st motion needle roller13H9513
-
51st motion ball bearingADU7619
-
6Bearing clip22G850
-
71st motion shaft drive gear, 29 teethDAM2925
-
8LocktabDAM4000
-
9Nut2A3548
-
10Layshaft, 3 step typeDAM3187
-
11Laygear, 15.20.25.29 teeth-without A plus marking grooveDAM3169
-
11Laygear, 15.21.26.30 teeth-with A plus marking grooveDAM4931
-
12Needle roller for laygear small end13H9513
-
13Needle roller for laygear large endCHM141
-
14Laygear thrust washer small .124”-.126” (3.1-3.20mm)DAM3181
-
14Laygear thrust washer small .127”-.129” (3.22-3.27mm)DAM3182
-
15Laygear thrust washer large22G860
-
16Reverse gear, was DAM8046TUB10020
-
17TUJ10001
-
18Reverse gear shaftDAM8038
-
193rd motion shaft with larger nose end .709” (18mm)DAM7484
-
211st & 2nd synchronizer hub, was 22G2263DAM7455
-
22Ball for synchronizer (3 per hub)BLS107
-
23Spring for synchronizer (3 per hub)22G2262
-
243rd gear, 21 teethDAM4933
-
253rd gear bearing was 88G496AAU1816
-
26Thrust washer22G947
-
28Spring for 2nd/3rd gear pegs22G154
-
292nd gear, 26 teeth, use with [LINK]DAM3168[/LINK] / [LINK]DAM3169[/LINK] laygear22G1094
-
292nd gear, 26 teethDAM4932
-
302nd gear needle roller was 88G495AAU1816
-
312nd gear washer22G839
-
323rd/4th synchronizer hubDAM7456
-
331st gear, 31 teeth22G1096
-
341st gear bearing, was 88G494AAU1815
-
363rd motion shaft ball bearingAAU1365
-
37Bearing clip, was 22G72ADU4992
-
38Shim, 3 thouGUG705645GM
-
38Shim, 10 thouGUG705646GM
-
40Locating plate2A3581
-
41LocktabDAM2377
-
42Retainer screw, UNC 5/16”x 3/4” long - Was 7/8” longSH505061
-
4318 teeth final drive pinionDAM2679
-
4319 teeth final drive pinion, see [LINK]CWP3-1[/LINK]/[LINK]CWP3-2[/LINK]DAM2808
-
44Pinion locktabDAM6140
-
45Locking nutDAM7485

'A' Plus gears have a different gear pitch and angle. The gears that are specifically 'A' plus have a slight central identification groove all the way round the outside edge of the main teeth.