Label |
Part No |
Description |
Quantity |
Comments |
|
1 |
18G8085 |
Gearbox lock tab kit |
1 |
Not shown - N.L.A |
|
2 |
GFK5170 |
Gearbox case, front block to gearbox bolt |
5 |
1 also on 22H983 |
|
3 |
GFK5180 |
Gearbox case, rear block to gearbox set screw |
4 |
1 also on front |
|
4 |
BH604141 |
Bolt for dowel on front was BH604140 |
1 |
1/4”UNF 13/4”l ong |
|
5 |
22H983 |
Case to block rear dowel |
1 |
N.L.A |
|
6 |
FHS2409 |
Stud, rear stud for thin flange block |
2 |
N.L.A |
|
6 |
FHS2410 |
Stud, rear stud for thick flange block |
2 |
5/16” UNF 11/4” long |
|
7 |
2A3502 |
Gear change linkage bush |
2 |
|
|
8 |
13H577 |
Gear change oil seal |
1 |
|
|
9 |
53K266 |
Stud for diff housing long 3/8” UNC x 45/8” Except Rod change |
4 |
N.L.A use TAM1617 |
|
9 |
TAM1617 |
Stud for diff housing long 3/8” UNC x 45/8” Except Rod change |
4 |
Chemi black |
|
9 |
22G1834 |
Stud for diff housing long 3/8”UNC x 43/8” N.L.A use 51K282 |
2 |
Rod change only |
|
9 |
51K282 |
Stud for diff housing long 3/8”UNC x 43/8” Chemi black |
2 |
Rod change only |
|
9 |
CHS2624 |
Stud for diff housing short 3/8” UNC x 3” or bolt 2 1/4”BH506181 |
2 |
Rod change only |
|
10 |
53K1471 |
Stud for diff housing, 5/16”UNC x 3”thread |
3 |
Can use 51K885 or DAM7760 Bolt |
|
11 |
22A152 |
Long stud for flywheel housing, 5/16”UNC 21/4”long |
6 |
or DAM7759 bolt 1.13/16 |
|
12 |
53K547 |
Short stud for flywheel housing 5/16”UNC 11/2”long |
3 |
or DAM7756 bolt 1.0625”long |
|
13 |
53K1474 |
Stud for speedo drive housing cover 5/16”UNC 33/4”long |
3 |
or DAM7761 bolt 31/4”long |
|
14 |
22A153 |
Dowel for diff housing |
2 |
N.L.A |
|
15 |
22A97 |
Dowel for flywheel housing |
2 |
N.L.A |
|
16 |
22A13 |
Dowel for speedo drive housing |
2 |
N.L.A |
|
17 |
22A74 |
Diff housing locktab, pre rod (Remote type only) N.L.A |
1 |
N.L.A - By 1982 locktabs were no longer fitted. |
|
17 |
42H500 |
Diff housing locktab, rod change N.L.A |
1 |
N.L.A - By 1982 locktabs were no longer fitted. |
|
18 |
22A251 |
Diff housing locktab. N.L.A |
1 |
N.L.A - By 1982 locktabs were no longer fitted. |
|
19 |
2A3505B |
Upper gasket for diff housing. Fits All |
1 |
From about 1982 Rover used RTV sealant GAC8000 instead of all these gaskets |
|
20 |
2A3506B |
Lower gasket for diff housing. Pre-rod change |
1 |
From about 1982 Rover used RTV sealant GAC8000 instead of all these gaskets |
|
21 |
22G1836 |
Lower gasket for diff housing. Rod change |
1 |
From about 1982 Rover used RTV sealant GAC8000 instead of all these gaskets |
|
22 |
88G302 |
Idler gear bearing with 1.004” 25.5mm O/D |
1 |
3 synchro |
|
22 |
13H7848 |
Idler gear bearing with 1.065” 27.05mm O/D |
1 |
4 synchro |
|
22 |
DAM3745 |
‘A’ plus idler gear bearing 1.375” 34.92mm O/D |
1 |
0.750” 19mm l/D |
|
22 |
TUK100320 |
‘A’ plus idler gear bearing 1.375” 34.92mm O/D was AHU1707 |
1 |
0.875” 22.225mm l/D |
|
23 |
22G1141 |
Clip for 3 synchro case where 88G302 fitted |
1 |
N.L.A |
|
23 |
51K3565 |
Circlip 4 synchro, where 13H7848 fitted |
1 |
|
|
24 |
DAM5219 |
Speedo drive housing cover, was 88G207 |
1 |
|
|
25 |
22A541B |
Gasket for housing, non genuine |
1 |
|
|
25 |
GUG705569GM |
Gasket for housing, genuine |
1 |
|
|
26 |
2A3626 |
Speedo drive case plate |
1 |
|
|
27 |
GUG705564GM |
Gasket for speedo drive case plate, was 2A3627 |
1 |
|
|
28 |
22A335 |
Oil strainer |
1 |
N.L.A - Use C-AHT54 |
|
29 |
22A341 |
Suction pipe sealing ring |
1 |
|
|
30 |
22A388 |
Lock tab |
1 |
N.L.A - By 1982 locktabs were no longer fitted. |
|
31 |
22A1365 |
Lock tab |
1 |
N.L.A - By 1982 locktabs were no longer fitted. |
|
32 |
22A337 |
Oil suction pipe 850cc |
1 |
N.L.A - Use C-AHT54 |
|
32 |
22G1150 |
Oil suction pipe 998cc to 1275cc |
1 |
N.L.A - Use C-AHT54 |
|
33 |
GUG705556GM |
Pipe to case and flange gasket, was 22A542B |
2 |
|
|
34 |
2K4874 |
Locktab |
1 |
N.L.A |
|
35 |
2A3606 |
Oil suction sealing ring - case to block |
1 |
|
|
36 |
DAM7355 |
Magnetic drain plug |
1 |
|
|
37 |
AED172 |
Washer for drain plug |
1 |
|
|
38 |
GUG703038SG |
Gearbox to enqine gasket, was AJM502, GUG3007SG |
1 |
|
|
39 |
AHU1959 |
Seal (half moon) was 12G2947 |
1 |
See CAM6548 also |
|
39 |
CAM6548 |
Seal (half moon) solid type, easy fit |
1 |
|
|
40 |
13H7286 |
Bush for gear lever steady bar |
1 |
|
|
41 |
AHU1672 |
Gearchange oil seal was 13H6862 |
1 |
Rod change |
|
42 |
CHS2514 |
Stud 5/16” UNC 1 3/4” long for speedo cover housing |
1 |
|
|